Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Steele Creek Homeowners
A missing or rusted-out cap is the single most common cause of the water damage we see on chimneys around Steele Creek. Rain runs straight down an open flue, soaks the smoke chamber, and works its way into the mortar until the crown starts crumbling and the ceiling below the fireplace shows a brown stain. Birds, squirrels and raccoons treat an uncapped flue as a ready-made den. A proper cap and a sound crown close that door.
Our technicians have up to 12 years of experience with the full chimney system, and we inspect before we recommend anything. If the crown is intact and only the cap needs replacing, that’s what we’ll tell you. We answer 24/7 at (888) 848-8714, and we can often work a Steele Creek cap or crown job into the same day.
What Our Chimney Cap & Crown Service Includes
We handle the top of the chimney the same way we handle the flue: diagnose first, then fix the actual problem with professional-grade materials. Here’s what each part of the work involves.
Cap Installation
A chimney cap is the screened metal cover that sits over the flue opening and keeps rain, animals and debris out while letting smoke escape. You need one if your flue is open to the sky, or if the existing cover is a thin hardware-store model that’s already bending. We install caps from Gelco and Famco, sized to your flue, and we set them so they shed water away from the crown rather than pooling on it.

Cap Replacement
Caps fail from rust, loose legs, torn mesh and storm damage, and a cap that’s rattling or missing screens stops doing its job long before it falls off. You’ll usually notice it as water in the firebox after rain, or birds nesting on the smoke shelf. We pull the old cap, check the flue tile and crown underneath for damage the failing cap may have caused, then fit a replacement that matches the flue dimensions rather than a universal cover held on with a strap.

Crown Repair
The crown is the concrete slab on top of the chimney that sheds water away from the masonry below it. Hairline cracks are normal as concrete cures, but cracks wider than a hair, a crown that’s pulling away from the flue tile, or chunks that have spalled off all let water into the brick. We repair crowns with a mortar mix formulated for chimney work rather than a generic patching compound, and we shape the crown so it drains properly instead of holding water at the edges.

Crown Coating
Crown coating is a flexible, waterproof membrane applied over a crown that’s sound but showing surface cracking or weathering. It’s the right call when the crown is structurally intact and you want to stop small cracks from becoming a rebuild. We clean and prep the surface first, because a coating over dirt and loose material won’t bond, then apply the coating across the full crown and down over the drip edge.
Multi-Flue Cap
A multi-flue cap covers two or more flue openings under one top plate, which is common on larger chimneys where a separate cap for each flue looks cluttered and traps debris between them. You need one when your chimney has multiple flues and a single small cap leaves the gaps exposed, or when individual caps keep getting knocked loose. We measure the full footprint, build the cap to fit, and screen every flue opening so nothing gets in between them.
Custom Cap
Custom caps are built for chimneys that don’t fit standard sizes: oversized flues, unusual masonry shapes, or a homeowner who wants the cap to match the house. You’d go custom when a stock cap leaves gaps, sits crooked, or blows off in wind. We take exact measurements on site, then have the cap fabricated in a heavy-gauge metal so it holds its shape and stays put.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with six professional chimney product lines, and the one that matters most at the top of the chimney is the cap. Gelco and Famco caps are the two we install most often, because both are built from heavier metal than the boxed covers sold at hardware stores and both come in sizes that actually match a real flue. We know where these caps wear first: the mesh screens, the mounting legs, and the seam where the top plate meets the side panels. When we replace a cap, we’re matching the new one to your flue dimensions so it doesn’t repeat the failure.
For the flue and crown work underneath, we use HeatShield ceramic resurfacing when the flue is deteriorating, and DuraFlex flexible liner systems when a flue needs relining rather than resurfacing. Those products come into play after a cap or crown job reveals damage the old cap let through. Whether you have a Gelco cap, a Famco cap, or any other make, we can help.
Signs You Need Chimney Cap & Crown Right Now
- Water in the firebox after rain. If you find damp ash, rust on the damper, or a water stain on the firebox walls after a storm, the cap or crown is letting water in. Left alone, that moisture works into the masonry and shows up as a ceiling stain months later.
- Cracks or crumbling on the crown. Look at the top of the chimney from the ground with binoculars. Cracks wider than a hair, or concrete flaking off the edge, mean water is getting into the brick below and freezing in cold weather, which pushes the masonry apart.
- Animals or birds around the flue. Scratching, chirping, or a nest visible at the flue opening means the cap screens are missing or torn. A capped flue should be closed to wildlife, and an open one invites animals down into the smoke chamber.
- White staining on the brick. A chalky white residue on the chimney’s exterior is a sign of moisture moving through the masonry. It often traces back to a failed crown or a cap that drains water down the side of the chimney instead of away from it.
- A cap that’s loose, rusted, or missing. A cap that rocks in the wind or has rusted through won’t survive the next storm. If it’s gone entirely, your flue has been open to the weather since the day it came off.
Our Chimney Cap & Crown Process – Step by Step
- 1
We look at the whole top of the chimney, not just the cap. Before anyone quotes a replacement, we get on the roof and check the cap, the crown, the flue tile, and the top courses of brick as one system. A new cap on a crumbling crown just traps water against failing concrete.
- 2
We show you what we found. We take photos of the crown cracks, the failed cap, or whatever else is going on, so you’re looking at the evidence rather than taking our word for it. If the crown has years left in it, we say so and quote only the cap.
- 3
We give you a written estimate, priced per job. The estimate lists what’s being replaced, what material we’re using, and the price before any work starts. There’s no charge for the estimate, and no surprise additions once we’re on the roof.
- 4
We do the work with professional-grade materials. Caps go on level and secure, crown repairs get shaped to drain, and coatings go over a properly prepped surface. We don’t patch to pass an inspection; we build it so it holds through the seasons.
- 5
We clean up and walk you through the finished job. You get photos of the completed cap or crown, and a clear explanation of what to watch for and when the next inspection is due. One call covers the sweep, the inspection, the cap and the crown.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Steele Creek?
A typical cap installation in Steele Creek runs $150 – $400 depending on flue size and whether it’s a single-flue or multi-flue setup. Crown repair, which involves removing loose material and rebuilding the slab, typically runs $300 – $700. Crown coating on a sound crown is usually the lower end of that range. Custom fabrication for an unusual chimney shape will sit above the standard cap range.
What affects price most: the number of flues, the size and pitch of the roof, whether the crown needs a full rebuild or just repair, and whether the work uncovers damage to the flue tile underneath. Access matters too; a steep roof takes more time to work safely than a flat one.
The way to avoid overpaying is to get evidence before you agree to anything. If someone quotes a full crown rebuild without showing you photos of the cracks, ask to see them. We include photos with every estimate. If the crown is sound and only the cap has failed, replacing the cap alone is the honest answer, and we’ll say so.
Your written estimate sets the final price. Call (888) 848-8714 for an exact quote; estimates are free.
Chimney Cap & Crown Near Steele Creek – Our Service Area
We work on chimneys across Steele Creek and the surrounding neighborhoods, including Mountain Island, Belmont, Cramerton, Pineville and the Charlotte neighborhoods of Dilworth, Myers Park, SouthPark, Eastover and Quail Hollow. Response times depend on where you are and what’s on the schedule, but we can often reach nearby addresses the same day. You can read more about our full chimney sweep and inspection services in Steele Creek, or look at our chimney cap & crown work in Mountain Island if you’re just across the river.
Serving Steele Creek, NC – Our Local Coverage Area
We serve Steele Creek and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Steele Creek
A chimney cap is the screened metal cover over the flue opening that keeps out rain, animals and debris; the crown is the concrete slab at the very top of the chimney that sheds water away from the masonry. Both sit at the top of the system and both protect the flue and brick below from water. When either one fails, moisture gets into the chimney and the damage shows up lower down. We repair or replace both as part of one job.
A standard cap installation usually takes under an hour once we’re on the roof. Crown repair takes longer, often a few hours, because the old material has to be removed and the new slab shaped and finished. Custom caps take extra time because they’re fabricated to measure. We’ll tell you the expected time in the estimate so you can plan around it.
Cap installation typically runs $150 – $400, and crown repair typically runs $300 – $700 depending on the extent of the damage. Multi-flue and custom caps sit at the higher end. The written estimate sets the final price, and there’s no charge for the estimate itself. Call (888) 848-8714 for an exact quote; estimates are free.
Yes. Gelco and Famco are the two cap lines we install most often, and we also work on caps from other makers. We check the mesh, the mounting legs and the top plate seams, since those are the parts that fail first. If the cap is beyond repair, we’ll quote a replacement rather than trying to patch rusted metal.
We can often get to a Steele Creek cap or crown job the same day, depending on the schedule and roof access. We answer 24/7 at (888) 848-8714, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. We’re closed on Saturday.
We stand behind the work we do, and the materials we install come with the manufacturer’s warranty on top of that. Ask us about coverage for your specific cap or crown repair when we give you the estimate. We’ll explain what’s covered and for how long before you commit.
Clear access to the fireplace and the roof if possible, and note any water stains, animal sounds or drafts you’ve noticed so we can check those areas first. You don’t need to do anything on the roof itself; that’s our job. If you have photos of the crown or cap from the ground, they help us plan the visit. Call (888) 848-8714 to book.
Schedule Your Chimney Cap & Crown Service in Steele Creek Today
A failed cap or crown only gets worse with the next storm. We inspect first, show you the photos, and quote a written price before any work starts, so you know exactly what you’re paying for and why. Call (888) 848-8714 for a free, no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. One call covers everything your chimney needs.
Written by the team at Chimney Sweep Steele Creek.